Ordering no:
Female cable connector with cable clamp, CRIMP connection, shieldable, cable outlet 4 - 6 mm
Female cable connector with cable clamp, CRIMP connection, shieldable, cable outlet 4 - 6 mm, Series 581
Available numbers of contacts
99 2010 700 04
M16 IP40 female cable connector, Contacts: 4, 4,0 - 6,0 mm, shieldable, crimp (Crimp contacts must be ordered separately), IP40
M16, series 581, Miniature connectors
| Order number |
99 2010 700 04
|
| Connector locking system | bolted |
| Termination | crimp (Crimp contacts must be ordered separately) |
| Wire gauge (mm) | see crimp contacts under accessories |
| Cable outlet | 4,0 - 6,0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 100 °C |
| Lower limit temperature | -40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰Ω |
| Contact material | depending on crimp contact (accessory) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 29 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2014 700 05
M16 IP40 female cable connector, Contacts: 5, 4,0 - 6,0 mm, shieldable, crimp (Crimp contacts must be ordered separately), IP40
M16, series 581, Miniature connectors
| Order number |
99 2014 700 05
|
| Connector locking system | bolted |
| Termination | crimp (Crimp contacts must be ordered separately) |
| Wire gauge (mm) | see crimp contacts under accessories |
| Cable outlet | 4,0 - 6,0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 100 °C |
| Lower limit temperature | -40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰Ω |
| Contact material | depending on crimp contact (accessory) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 30.073 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2022 700 06
M16 IP40 female cable connector, Contacts: 6 DIN, 4,0 - 6,0 mm, shieldable, crimp (Crimp contacts must be ordered separately), IP40
M16, series 581, Miniature connectors
| Order number |
99 2022 700 06
|
| Connector locking system | bolted |
| Termination | crimp (Crimp contacts must be ordered separately) |
| Wire gauge (mm) | see crimp contacts under accessories |
| Cable outlet | 4,0 - 6,0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 100 °C |
| Lower limit temperature | -40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰Ω |
| Contact material | depending on crimp contact (accessory) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 30.073 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Downloads
Data sheet
99 2026 700 07
M16 IP40 female cable connector, Contacts: 7, 4,0 - 6,0 mm, shieldable, crimp (Crimp contacts must be ordered separately), IP40
M16, series 581, Miniature connectors
| Order number |
99 2026 700 07
|
| Connector locking system | bolted |
| Termination | crimp (Crimp contacts must be ordered separately) |
| Wire gauge (mm) | see crimp contacts under accessories |
| Cable outlet | 4,0 - 6,0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 100 °C |
| Lower limit temperature | -40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 800 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰Ω |
| Contact material | depending on crimp contact (accessory) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 29.823 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Downloads
Data sheet
99 2062 700 08
M16 IP40 female cable connector, Contacts: 8 DIN, 4,0 - 6,0 mm, shieldable, crimp (Crimp contacts must be ordered separately), IP40
M16, series 581, Miniature connectors
| Order number |
99 2062 700 08
|
| Connector locking system | bolted |
| Termination | crimp (Crimp contacts must be ordered separately) |
| Wire gauge (mm) | see crimp contacts under accessories |
| Cable outlet | 4,0 - 6,0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 100 °C |
| Lower limit temperature | -40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰Ω |
| Contact material | depending on crimp contact (accessory) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 29.833 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Downloads
Data sheet
Contact to customer service
Do you have any questions regarding our products or do you wish an individual offer?